Electric Tankless Water Heater Installation Requirements
Installation With Hard Water
Electric tankless water heater installation requirements become more complex when you have hard water in the system. In general, there are some issues when it comes to operate tankless water heaters with hard water as I explain thoroughly in this article.
You should run your municipal water through a water softener. Without a softener, your heater would probably soon quit working as the water feed will become plugged with minerals.
The degree of scaling that occurs in potable hot-water systems is dependent on the type of hardness, the temperature rise, and changes in pressure. The hotter the delivery temps, the greater the amount of scaling. For example, tankless water heaters targeting 120°F are less susceptible to scaling than tankless water heaters set for 140°F, and so on.
Most of the precipitated minerals in tankless water heaters are flushed through the system because of the high velocity of the water zipping through the heat exchanger. However, tankless water heaters should be installed so that the heat exchanger can be chemically cleaned. Isolation valves and boiler drains easily solve this issue, and several manufacturers, as well as third-party vendors, have flush kits. Noritz and a few others have in-line filters they claim allow their tankless water heaters to be used in hard-water conditions.
Tankless water heaters have sensors that monitor the heat-exchanger operation, and scaling inside the heat exchanger’s tubing will act as an insulator, which will eventually lead to a fault code for over-temperature conditions. Once that occurs, a thorough chemical flush will need to be done before the unit can be placed back into service. Because of the personal and property safety issues involved, this work is best handled by licensed professionals trained in the procedure.
Hard water is typically made up of calcium, magnesium, bicarbonates, and sulfates. A lab can provide details of what’s in the water. Water hardness is expressed in grains; water measuring over 4 grains is typically considered the threshold for using a water softener.
Before running hard water through a tankless heater:
- Have the piping set up to facilitate chemical cleaning.
- Install a prefilter designed to mitigate the hardness.
- Have your installer check the inlet water pressure while operating the heater under full-flow conditions, and measure the delivery GPM flow rate (timed delivery into a bucket with gallon marks). This sets a benchmark for the new, clean heat exchanger, and provided that the inlet pressure is the same for subsequent tests, the full-flow outlet GPM test will reveal if any scaling has created a buildup within the heat exchanger.
Hello, I am Marcio. I am an architect and designer, alma mater is Mackenzie. Retired in theory, but an architect never retires completely. Along with architectural projects, I am a filmmaker and have completed some short documentaries. Filmmaking and design are my passions. In HomeQN I write about home decoration and foundations. The goal is to teach homeowners to DYI as much as possible, and when this is not possible, enable them through knowledge, to evaluate service quotations and choose the best service technicians.
We have some articles that I would like to recommend to the readers.
Foundation Repair And Maintenance
We have described here the type of foundations, what is a foundation inspection and what should be included in a good foundation inspection checklist. We can discover problems in the foundation to make us ask ourselves if it is safe to live in a house with foundation problems and what entails a foundation repair, if it is covered by homeowners insurance and its costs.
To repair a foundation, the service provider requires an underpinning system using piers: push piers vs helical piers where helical piers are preferable for residential real estate objects, despite their costs. Also when you compare helical piers with concrete footings, we can determine that helical piers are more cost-efficient than concrete footings, in my opinion.
We have water in the crawlspace: I explain what to do when the crawlspace is flooded, if it is normal to have water in the crawlspace after a heavy rain, and the importance to perform a crawlspace waterproofing thereafter, normally by installing a vapor barrier.
I describe how to improve the air quality in the crawlspace and to accomplish this, I am reluctant to use lime powder in this article, where I explain the pros and cons, as I would be using lime powder only to avoid the dangers of raw sewage under house.
We discuss the sill plate replacement cost and how to avoid the outdoor sump pump freezing, because it happened to me once.
There are always new methods for repairing foundations. One of them that we investigate here is the Powerbrace foundation repair method.
Animals can be a problem when they live near the foundation: In the following articles we describe how to remove them and how to prevent them from digging and burrowing. The articles are about animals digging holes around the foundation or when they are burrowing below concrete, below a concrete slab, or between gaps in concrete footings, for example.
In regards to basements, I describe how to solve the hydrostatic pressure in the basement. I provide to you some reasons of why we will need a certified specialist to deal with a risky sewage backup in the basement because bacteria survives a long time in a contaminated sewage and also we discuss how to deal with a basement drain backing up in general and when it happens when flushing the toilet, something that is not a DYI project at all.
I explain here the process of concrete lifting or concrete raising, that can be done through mudjacking or slabjacking. We recommend the latter, which injects polyurethane foam.
There are some interesting articles here, in this Framing category. I refer to sistering floor joists, as a methodology to reinforce existing floor joists with some emphasis on sistering 2x6 floor joists or sistering with 2x8 instead, and about the building code for sistering joists, for sistering rafters, and the code for notching floor joists.
About water heaters, we have a complete guide about water heater types and their installation requirements, about power vent water heaters, and venting in tankless devices, and I also explain in detail the difference between a mobile home water heater and a standard water heater. I also describe in detail how to remove the heating element without an element wrench using just a socket, and how to protect your water heater against the effects of hard water, and how to fix leaking.
We have some few reviews when a water heater falls into our hands, such as the Titan product portfolio, Navien lineup, the Titan N-160 reviews, the most praised by our readers, and the Rinnai R94LSi .
I study several water heater capacities and tested 20-gallon water heater units, and a comparison between point of use and tankless water heaters.
We open a tankless water heater to show how does it look like inside a tankless water heater.
After the lifecycle of the water heater is over, I reveal to you different options to proceed with its disposal.